Plastic bottle - watering artifact

Watering meat is a troublesome thing. Watering with a water spray can accidentally pour it on the leaves, resulting in rotten heart and rotten stems. How to solve this pain point? Simple! A plastic bottle can be achieved

First step

Find a plastic bottle and keep the top plastic bottle cap. Don't throw it away

Step 2

Take off the plastic cover, hold the plastic cover with pliers and other tools in one hand, and bake the outside of the plastic bottle with a lighter over a low fire in the other hand to make it softer

Step 3

As shown in the figure below, find a toothpick and poke it slowly from the inside to the outside in the middle of the plastic cover. When poked, it should be stable, do not shake left and right, until a beautiful small cone is poked

Step 4

Poke out a beautiful cone. Don't worry about taking off the toothpick first. Put it in a ventilated place and dry it naturally. After it is completely shaped, take off the toothpick

Step 5

After the conical hole is made, we can properly cut off the tip at the top with scissors to let the water flow out

Step 6

The last step is to fill the plastic bottle with water and cover it with the cover made in advance! When watering, pinch the body of the plastic bottle, and small water can flow out of the bottle cap

Step 7

This kind of self-made watering pot has small water flow and will not flow to the heart of fleshy leaves, resulting in rotten heart, rotten stem and rotten leaves. It is better to use than the water pot occupied by fleshy food bought with money

Step 8

Of course, if the above operation is troublesome, you can directly buckle a hole in the bottle cap and insert the straw into the hole

Special attention should be paid to that the size of the hole on the bottle cap should be consistent with the diameter of the straw, otherwise it will leak

Plastic bottle cutting artifact, 100% rooting

Huahua has introduced a lot about the cutting of plastic bottles, but this method taught by Huahua today can have a higher rooting rate than other methods. Here is a detailed description of Gardenia as an example

Step 1

Usually form the habit of collecting plastic bottles. Don't throw away plastic bottles or drink bottles

Step 2

Cut off a section of Gardenia semi lignified branch, which is best to grow from half a year to one year. Cut the bottom of the branch 45 degrees obliquely with a wallpaper knife, so that the incision presents a horseshoe shape, increase the contact area with water, and it is easier to take root

Step 3

find 1 foam boards and cut a circle according to the diameter of the bottom of the foam. p>

Step 4

drill a small hole in the middle of the foam, then remove the bottom leaves of the Gardenia branches and insert them into the small holes of the foam board. p>

Step 5

Place the plastic bottle horizontally at the 1 / 3 position from top to bottom of the plastic bottle and cut it with a wallpaper knife. Be careful not to cut off the 1 / 3 of the upper part completely and leave a little so that the upper and lower parts can be connected together without breaking

Step 6

Pour water into the lower part of the plastic bottle. The water level accounts for about 3 / 4 of the lower part of the plastic bottle

Step 7

plugging the foam of Gardenia branches into the lower part of the plastic bottle, above the water. Ensure that the branches below the foam touch moisture. p>

Step 8

Put back the top half of the plastic bottle cap and wrap the incision with adhesive tape. Remove the lid from the plastic bottle

Step 9

Put the cutting device in a place with astigmatism and ventilation. After about 2-3 weeks, the branches will grow white roots, and there is no need to add water during the period

Plastic bottle seeding artifact, super fast germination

Autumn! It's the sowing season again. Are flower friends buying seedling pots and seedling blocks everywhere again? In fact, you don't have to spend the wronged money. Your plastic bottle is a super easy-to-use sowing artifact

Step 1

Prepare a plastic bottle, as shown in the figure, horizontally, up, middle and down, evenly cut into three parts, and put the middle one aside

Step 2

Fill the bottom plastic bottle with soil, water it thoroughly, and then sprinkle seeds

Step 3

Seal the incision with fresh-keeping film, moisturize and keep warm. Wait for 1-3 weeks, and the seeds will germinate

Step 4

When all the seedlings come out, you can tear off the plastic wrap! But the seedlings are too weak to withstand strong wind and low temperature. At this time, 1 / 3 of the plastic bottles we cut off can be used! As shown in the picture, just cover it like a hat, which not only improves the humidity, but also protects the seedlings