Lvluo is cutting like this. If you don't live, you come to me

Huahua is going to teach you a super simple green pineapple cutting method today! Just a stem! The green pineapple raised by flowers is cut by itself. The cuttings were picked up easily during the flower market without spending a penny. Come and have a look

1. Cut the leaves and the branches into small segments

When Huahua picked up the branches of lvluo, the leaves were a little wilted, but the stem was still fresh green. Huahua simply cut all the leaves directly, and then cut the stem into segments, each of which was 3-4cm long and had at least one node

2. Prepare cutting soil

Lvluo likes soft and clean soil. Huahua suggests that you first expose and disinfect the river sand and rotten leaf soil, and then mix them together. You can add some vermiculite to make the soil loose and breathable, which is more conducive to the rooting of lvluo

3. Let the branches lie on the soil

After the branches are cut, you can put them in a cool and ventilated place to dry the wound, and then spread them horizontally on the surface of the basin soil. If there are air roots on the nodes, let the air roots contact the soil

4. Pouring once permeable

After the branches are paved, pour water once. The water should be poured thoroughly. When you see the water flowing out of the drainage hole at the bottom of the basin, you can stop watering

5. Cover with transparent film for heat preservation and moisture retention

Now the temperature in some places in the North may be a little low, so cover the basin with a layer of transparent plastic film, tie it with a rope along the edge of the basin, and tie two small holes in the film to breathe. Move to a place with plenty of light indoors

6. Take root in about 15 days

While waiting for rooting and sprouting, pay attention to whether the soil is dry. Water it in time to make the soil moist, but don't pour too much, otherwise you will regret it in the rotten basin. Generally, in about 15-30 days, fresh green and shiny young leaves will be issued, and the root system has long been thick and white

7. Transplant into a pot

When the new leaves grow up, the number of leaves grows to 3-5. At this time, the root system also grows stronger and can be dug out and put into the basin. In order to reduce root damage, you can transplant with soil

Gardenia cutting like this, 100% live

When spring comes, gardenia lovers must be happy. They can not only wait to enjoy the flowers, but also cut and turn one pot into 10 pots. Gardenia cutting difficult to take root? Try the amphibious cutting method quickly. It's absolutely rooting! It's hard to die

1. Cut off the Gardenia branches

Try not to choose too tender branches. 1-2-year-old lignified branches are easier to survive. Cut the branches into sections at an angle of 45 degrees, 10 cm for each section, and put them in a ventilated place to dry for 1-2 hours to let the wound heal

2. Block the flowerpot drain hole

Light the candle, hold the candle upside down with your hand, let the melted wax drop to the drain hole, drop more for a while, and seal the drain hole. After you feel completely sealed, you can pour water to detect whether there is water leakage. Don't leak! Then pour out the water

3. Pour 3 / 5 of the soil into the basin

Dig some garden soil in the green belt of the community, expose it to the sun for sterilization, and then put it into the flower pot. The garden soil accounts for 3 / 5 of the flower pot

4. Lay another layer of river sand

First wash the river sand with water, then spread it flat and disinfect it in the sun, and then pour it into the flower pot. The river sand accounts for 1 / 5 of the flower pot. There is no need to mix with the garden soil

5. Pour water into the basin

Pour clean water into the flowerpot. It's best to pour it slowly along the edge of the basin to let the water soak the soil. Don't pour it until the water surface is about 1cm higher than the sand surface of the river

6. Stick branches into the soil

After the branch wound is dried, it can be inserted into the basin. Don't insert it too deep and let the branch stand stably. It is enough to insert 3-4 branches in one flowerpot, which is too dense and is not conducive to later growth. If the drain hole of the flowerpot is not tightly blocked, plastic bottles can also be used

7. Change water every week

Move the flowerpot to the scattered light, add clean water in time, keep the water surface 1 cm higher than the soil, pour out the water every 7 days and replace it with new water

8. Take root in about 15-20 days

After 15-20 days, gardenia will take root. If you use a flowerpot, poke the drainage hole inward from the bottom of the basin to make the water flow clean and put it in a well ventilated place. Wait until the soil is dry before watering. Don't worry about not being able to support anymore

The cutting of Chinese rose is so fast

Some flower friends like cutting, but they have been defeated repeatedly. There are 9 Black Rot in 10 times, which makes people helpless to doubt life. How can the cutting survival rate of rose be high? Come and learn the great God's vermiculite tray method, which can not only prevent black rot, but also make the root rub long, and 100% break the curse of "cutting will die"

1. Branches are more likely to survive after flowering

If you want to improve the survival rate, you can try to choose the branches after flowering, because the branches are relatively rich in nutrition

2. Pruning strip

Wipe and disinfect the scissors with alcohol, cut off the branches after 1-year-old robust rose flowers, and cut off the section with flowers. The incision should be flat. Keep the 2 sections at the bottom and insert them into the soil. The cut shall be chamfered 45 °

3. Soak in carbendazim

Soak the cut branches in carbendazim for sterilization and disinfection. Take them out after 20 minutes and dry them in a ventilated place. Cutting is always a black rot flower friend. Don't forget this step

4. Dip in rooting powder

Dip the bottom cut of rose branches with rooting powder or soak in 10 times diluted sugar water to improve the rooting speed

5. Select cutting soil

First, put vermiculite or river sand into the sun to sterilize, and then pour it into a transparent plastic bottle. The bottom of the bottle should be poked with several holes for drainage and ventilation

6. Put the plastic bottle on the tray

Find a tray or basin. Fill it with water. The water is 3-5cm high. Put the plastic bottle containing soil on it to let the soil absorb water and become moist

7. Stick branches into the soil

First poke a few holes in the soil, and then bury the rose branches. Put it under the scattered light and can't be directly exposed to the sun to prevent it from wilting. Usually, you don't need to water the soil. When you see that the tray water is gone, you have to add it

8. Rooting after 15-20 days

After about 15-20 days, you can see the white roots and green leaves in the transparent plastic bottle. Let the roots continue to grow for a few days, cut the plastic bottle, take out the branches with the soil and transplant them into a new flower pot

Cutting is very interesting

Don't miss this spring

Don't lose heart even if it's black and rotten

Try a few more times and you'll succeed

If you think Huahua's cutting super method is useful

Just share it with others