Cutting Rooting

Rose

1. For branches to be cutted, it is best to find strong branches that have bloomed and leave more leaves on the branches

2. Clean the incision with a sterilized blade and cut it across the board. The incision should be smooth

3. Soak the branches in carbendazim solution for two hours, take them out and dry them in a cool and ventilated place

4. Remove the leaves near the root of the branch for cutting

5, prepare foam board, drilling with scissors in the middle. p>

6. Prepare a water tank, basin, etc. for water

7, branches into the foam board, put on the water. p>

8, a few weeks later, you can take root. You can pick up the foam board at any time to observe the rooting. p>

Gardenia

1, tool preparation: knife, foam board, transparent adhesive tape, plastic bottle, screwdriver or scissors. p>

2. Prepare Gardenia branches to be cutted and ensure that the branches can be put into plastic bottles

3. Soak the branch incision in carbendazim solution or potassium permanganate solution for two hours, and dry it in a cool and ventilated place after disinfection

4. Cut the plastic bottle with a knife. Be careful not to cut it completely. Leave a little to connect the two parts of the bottle body

5, cut the foam board into a round shape, and put it into plastic bottle. p>

6. Use scissors or screwdriver to drill a small hole in the bottle cap for later ventilation

7, drill holes on the foam board and insert branches on the foam board. p>

8, add water to the bottle, put the foam board and branches into the bottle, and the water surface should be soaked through the roots of the branches. p>

9. Stick the bottle with tape

10. Put the plastic bottle with branches on the Nanyang terrace or the sunny windowsill, and it will take root in about 10 days

Rubber tree

1. Cut off the strong branches of rubber tree, about 10cm

2. Burn the branch incision with a lighter, or soak in potassium permanganate solution, and wait until there is no white juice flowing out of the incision

3. Clean containers such as glass bottles and add water

4. Remove the leaves near the root of the rubber branch and insert them into the water bottle

5. Put the hydroponic bottle in the sun, and after about half a month, the rubber tree will grow roots

Jasmine

1. Select robust Jasmine branches, which are hard to touch and have been lignified

2. Prune the branches of jasmine and cut off the yellow leaves and unhealthy leaves

3. Soak the incision in carbendazim solution for disinfection and sterilization, and then put it in a cool place to dry

(author: Su muying leaves the night rain source: HuaBa)

4. Remove the leaves near the root of the jasmine branch, insert it into a hydroponic flask and put it in the sun

(author: fruit is melon, source: Baidu knows)

5. In about a week, jasmine branches will take root

(author: fruit is melon, source: Baidu knows)

Green Rose

1. Select the vigorous growth of green pineapple

2. Cut off the robust cuttings with a length of about 10 cm, and clean the leaves with clean water

3. Apply carbendazim disinfection on the branch incision, dry it in a cool place, and remove the leaves near the root

4. The branches of green pineapple can take root in about half a month by inserting them into a hydroponic container and putting them in the sun

Camellia

1. Select strong Camellia branches

(author: imagination, creation, source: Camellia bar)

2. Remove the branches and leaves near the root of Camellia

(author: imagination, creation, source: Camellia bar)

3. Apply carbendazim to the incision for sterilization, and put the branches in a cool place to dry

4. Insert the branches into a container of water. You can also put some sponges and paper towels with good water absorption into the container, insert the branches on the wet sponge, and finally put it in the sun

5. It will take about two weeks to take root

Key points of rooting

1. The water must be clean

2. Branches and cuts should be disinfected

3. Try to leave more leaves on the branches, and the hydroponic flask should be placed in the sun, so that the leaves can photosynthesis and provide nutrients for the branches

Out of water into the basin

Whole soil

1. Prepare loose sandy soil and flower pots

(author: yueyingyou bamboo source: HuaBa)

2. Put the rooting flower seedlings on the soil and spread the roots evenly

(author: yueyingyou bamboo source: HuaBa)

3. Fill the pot with soil

(author: yueyingyou bamboo source: HuaBa)

4. Compact the soil

(author: yueyingyou bamboo source: HuaBa)

5. Water thoroughly until the water flows out of the permeable hole at the bottom of the flowerpot

(author: yueyingyou bamboo source: HuaBa)

6. Cut off excess branches and leaves to reduce water transpiration

(author: yueyingyou bamboo source: HuaBa)

7. Put the potted plants in a cool and ventilated place for a week. If there is no abnormality, you can bask in the sun

(author: yueyingyou bamboo source: HuaBa)

Half water and half soil

The way of half water and half soil into the pot is to put the rooting branches in the water and then fill the soil. Under the buffer effect of water, it can reduce the wear of soil on new roots and improve the survival rate

1. Prepare idyllic soil

(author: rice red jujube source: Rose Flower bar)

2. Prepare coal or vermiculite

(author: rice red jujube source: Rose Flower bar)

3. Prepare several disposable water cups

(author: rice red jujube source: Rose Flower bar)

4. The crushed coal cinder is mixed into the pastoral soil to loosen and breathe

(author: rice red jujube source: Rose Flower bar)

5. Use scissors to make a cut on the wall of the disposable cup, or drill several holes at the bottom of the cup

(author: rice red jujube source: Rose Flower bar)

6. Put the delimited cup into another intact disposable cup

(author: rice red jujube source: Rose Flower bar)

7. Prepare the rooting branches

(author: rice red jujube source: Rose Flower bar)

8. Cut off excess leaves to reduce water transpiration

(author: rice red jujube source: Rose Flower bar)

9. Add the soil to the previously treated folded cup

(author: rice red jujube source: Rose Flower bar)

10. Add water to the cup

(author: rice red jujube source: Rose Flower bar)

11. Put the rooting branches into water and fix them

(author: rice red jujube source: Rose Flower bar)

12. Hold the branch with your hand and add soil to the cup

(author: rice red jujube source: Rose Flower bar)

13. After the soil is added, take out the disposable cup on it

(author: rice red jujube source: Rose Flower bar)

14. Three days later, the seedlings and soil were moved into the large basin

(author: rice red jujube source: Rose Flower bar)

Hydroponic cutting is a very simple thing

As long as you master the trick, breeding flowers and plants is no longer a problem

(Note: the pictures come from the Internet and the copyright belongs to the original author. Due to restrictions, some pictures cannot be found and the author has not been marked. If your rights and interests are infringed, please contact Huahua wechat qdxixi or qq1273160598 for deletion or copyright payment.)< span>