Infusion tube watering method
Operation steps:
1. Find an abandoned complete infusion tube from home. If not, you can go directly to the pharmacy or clinic to get one p>
2. Find a clean plastic bottle full of water, and then use scissors to poke a small hole in the bottle cap. The size of the small hole is about the size of the needle tube. If the hole is too large, the water is easy to flow out p>
3. Turn the plastic bottle upside down, plug a disposable paper cup on the bottle mouth, and then insert the plug of the infusion pipe through the disposable paper cup and directly into the plastic bottle cap. You can put some small stones in the disposable paper cup in order to prevent the plastic bottle filled with water from skewing p>
4. Prepare a disposable plastic straw, cut the straw into a length of about 5-8cm with scissors, then insert the straw into the soil and insert the needle of the infusion tube into the straw p>
5. There is a switch on the infusion pipe, which can adjust the speed of water flow at any time. If you want to make the water flow faster, you can adjust it slower. Huahua suggests a larger plastic bucket. The bottle is relatively hard and is not easy to be squeezed, resulting in larger water flow p>
Plastic bag immersion basin method
Operation steps:
1. Find a bigger washbasin, make sure that the whole flowerpot can be put in, and then put the flowers such as green rose and Cyclamen into the washbasin p>
2. Find some transparent plastic bags to ensure that the plastic bag is watertight, then fill the plastic bag with water and tie the seal to ensure that the water will not leak out of the bag p>
3. Put the plastic bag with water in the washbasin, and then use a needle to pierce several small holes in the plastic bag, so that the water in the plastic bag can flow out slowly, about 2-4, not too much p>
4. After the hole is pierced, the water will flow out of the plastic bag slowly, and then penetrate into the interior of the flowerpot through the pores at the bottom of the flowerpot, so that the root system can absorb water. There is no need to water for about ten days and a half months, and because the water flow is slow, it is not afraid of rotten roots p>
Cover it with plastic bags
Operation steps:
1. If you go out for a short time, you can water the flowers at home once before you go out, until you find water leaking from the bottom of the basin p>
2. Find a big plastic bag and cover the whole flowers at home, so as to achieve the purpose of heat preservation and moisture retention. In order to avoid damage to the leaves, you can find a few small wooden sticks to support the whole plastic bag p>
3. When the flowerpot is covered with a plastic bag, some holes can be left at the bottom of the flowerpot for internal air and external circulation of the plastic bag to prevent the flowers at home from getting sick due to lack of ventilation p>
Cloth strip water absorption device
Operation steps:
1. Fill a cup with water, and then put it higher than the flowerpot. Plug one end of the soaked thin cloth strip or shoelace into the cup filled with water and the other end into the flowerpot, so that the water can slowly penetrate into the flowerpot along the cloth strip p>
2. This method is only suitable for the evaporation of water in the South platform. If it is put in the South platform for a long time, it will only accelerate the wilting of water. If it is put in the South platform for a long time, it will only be suitable for the wilting of water p>
Automatic watering method for plastic bottles
Operation steps:
1. First, prepare a clean plastic bottle for standby p>
2. It takes about 3-5 nails to drill holes in the plastic bottle cap p>
3. Fill the plastic bottle with water, and then screw on the perforated bottle cap p>
4. First pour water once, then turn the plastic bottle upside down, tilt 45 °, and directly insert it into the flowerpot. The water in the plastic bottle will slowly penetrate into the flowerpot from the bottle cap, so as to automatically water the flowers p>
Straw automatic watering method
Operation steps:
1. Prepare 2 straws and a larger plastic bucket p>
2. Make two holes in the plastic bucket up and down, and the size of the hole is the same as that of the straw. Then insert the straw into the plastic bucket, stick it with glue, and then stick the lower ends of the straw together with adhesive tape p>
3. When the glue is dry, fill the plastic bucket with water, and such an automatic watering device will be ready p>
Huahua will introduce these today p>
Have all flower friends learned p>
Why don't you take advantage of the days when you go out during the Chinese new year
Make one quickly
Don't let the flowers at home wilt due to lack of water p>