Plastic bottle cutting rose, take root in 7 days h2>
Before long, it's time for roses to bloom. Take advantage of the spring to quickly cut more pots, and the home will become a rose garden p>
Operation steps:
1. Find a clean plastic bottle and cut it from the top half with scissors. Be careful not to cut it all off, leaving a small part on one side p>
2. Prepare the rose branches needed for cutting. Pay attention to the branches that must be stronger, so that they can survive more easily. The lower end of each section of branches shall be chamfered 45 ° to make it easier to take root p>
3, prepare a foam board, cut the foam board into a smaller circle than the plastic bottle mouth, that is, the foam board can be taken out of the bottle at will. Then the center of the foam board is stabbed with a small hole to allow the branches of the rose to be inserted. p>
4, add some water to the plastic bottle, then put the foam board with the rose branches into the plastic bottle, arrange the leaves of the rose leaves, let the leaves expand as far as possible, and keep the water level in the plastic bottles as far as possible. p>
5. Find the black adhesive tape and wrap it tightly around the joint of the plastic bottle to seal it p>
6. Then put it in a place with good indoor scattered light for 1 week, and then transfer it to direct sunlight. It only takes about 1 week to take root p>
7. After rooting, in order to ensure the survival rate, it can be planted first. Prepare a disposable cup, first add a layer of perlite at the bottom, then add soil such as nutrient soil and cinder, and put the rose branches in p>
8. When the root system grows a little, prepare loose and breathable nutrient soil, and put the rooted rose branches directly into the basin. Usually apply compound fertilizer and potassium dihydrogen phosphate, and the rose will soon grow up p>
Plastic bottle cutting triangular plum, the root system is thick and strong h2>
As a northerner, Huahua sometimes really envies the south. After all, the triangle plum in the South can climb the wall if it wants to climb the wall. It can even climb several meters high. It's really beautiful p>
Operation steps:
1. Prepare robust Prunus mume branches, preferably semi lignified branches, with a length of about 10-15cm. Leave 2-3 leaves at the upper end, and cut the lowest end of the branches obliquely by 45 ° with a sharp knife, and then soak them in rooting water p>
2. Prepare the flower mud block, cut the flower mud block into small pieces with a length, width and height of 3cm, and then insert the triangular plum branches p>
3. Put the cuttings of triangle plum together with the flower mud into the tray, then find a clean plastic bottle to cover it and put it in a place with good light scattering indoors. Pay attention to moisture and ventilation p>
4. It will only take about one month to see the white roots passing through the flower mud, indicating that the cutting of triangular plum has taken root p>
5. After taking root, put the triangle plum together with the flower mud in the basin, put it in a cool and ventilated place to ease for a period of time, and then put it in a well lit place in nanyangtai for normal maintenance. The triangle plum will soon grow up p>
Plastic bottle cutting meat, 1 pot per minute to 100 pots h2>
It's time for more meat in spring. If you want to get more meat quickly, there's only leaves left p>
Operation steps:
1. Roll down the leaves from the succulent mother plant and air them in a place with good light scattering indoors to avoid wound infection with black rot p>
2. It's easy to poke a small hole in the middle part of the bottle with a pair of scissors. It's best to poke a small hole in the middle part of the bottle with water and a sharp knife p>
3. First add water into the bottle, and pay attention that the water level must not exceed the poked water inlet. Then insert the fleshy leaves drying the wound into the plastic bottle, and then put them in a place with good light scattering. If you find that the water at the bottom is reduced, add a little. If you find that the leaves are wilted, you can spray water p>
4. The water in the plastic bottle will continuously evaporate and increase the humidity, so as to promote the fleshy leaves to take root and sprout as soon as possible. When the fleshy cutting leaves take root and sprout, they can be transplanted into the pot soil p>
5. When removing the rooting leaves from the plastic bottle, be careful to avoid damaging the newly grown roots. If you are really worried, you can also choose to cut the plastic bottle with scissors, add some water at the bottom, and fix the fleshy blade directly with tape p>
About plastic bottle cutting
Huahua is introduced here p>
Flower friends also want to know which flower cuttings
Leave a message to Huahua p>