Gardenia cutting

1. Trim the branches after Gardenia

The Gardenia branches after withering are the most robust, and the survival rate of cutting with such branches is the highest

2. Treatment of cuttings

The cut Gardenia branches are treated and then cutted. The lower end of the branches is cut into an inclined plane, and the length of the branches is more than 10cm

3. Sterilization and drying

Soak the Gardenia in the potassium permanganate solution for about 30 minutes

4. Making greenhouse

Prepare a large plastic bottle and cut it in the middle with a knife. Don't cut it

5, making foam support plate

prepare a foam board, cut it into a size similar to plastic bottle, put a few holes in the foam board and insert the dried Gardenia into the hole. p>

6. Put the branches into the greenhouse

put the Gardenia on the foam board into the plastic bottle with clear water and tape the plastic bottle to seal. p>

7. Cuttage Gardenia colonization

About 15-20 days, gardenia grows strong white roots before colonization

Rose cutting

1. Prune the branches after rose flowers

After the flower withers, the rose needs to be trimmed after the flower in order to burst the pot faster. It's a waste to throw away the cut branches. It's better to use cuttings~

2. Pruning rose cuttings

Select strong dark green branches for cutting, and keep at least one bud point at the bottom of the cuttings

3. Insert into soil or soak in water

Vermiculite can be used as the matrix for soil insertion. Before inserting rose, it can be poured through with diluted potassium permanganate solution to ensure that at least one bud is buried in the soil, and the tray should be filled with water

Chinese rose can also choose hydroponic cutting for rooting. Just choose clean tap water. You can add a little rooting powder to the water appropriately

4. Astigmatism curing

Put the cut roses in the astigmatism environment for maintenance, avoid strong light and fertilization, and spray a little thin foliar fertilizer every week

5. Cutting rose planting

After about 30 days, the cut rose branches grow white fibrous roots and can be planted in pots

6. Pour through basin soil

The soil of the planting basin must be watered thoroughly. It is best not to choose a too large flowerpot for the planting basin, otherwise it is easy to accumulate water

Chrysanthemum cutting

1. After chrysanthemum flower pruning

After the chrysanthemum flower withers, a large pruning should also be carried out to reduce nutrient consumption. At this time, the cut branches have accumulated a lot of nutrients and strong disease resistance. It's most suitable for cutting

2. Pruning chrysanthemum cuttings

Select the strong and emerald green branches, leave 2-3 large leaves, cut off the rest, leave 1cm below the bottom leaves, and cut off the rest

3. Matrix selection

The substrate of cuttings can be mixed with peat soil and perlite. Before inserting branches, you can poke holes in the substrate with a toothpick

4. Dip rooting powder into the soil

Dip the cuttings into the rooting powder prepared in advance, and the depth of insertion into the soil is about 2cm

5. Watering and curing

After cutting, pour water, put it in a cool and ventilated place, and spray water 1-2 times a day

6. Colonization after rooting

After about 20-30 days, the cut chrysanthemum will grow fine roots and new leaves. At this time, take it out of the hole plate and move it into the flower pot

Rhododendron cutting

1. Prune the branches after the azalea

From budding in early spring to withering of Rhododendron, nutrients are absorbed in a few months. At this time, the branches of Rhododendron have the best maturity, which is robust and does not undergo lignification, so it is suitable for cutting

2. Prune branches

Choose strong and green branches. The old branches are not easy to survive. Cut the incision into a plane with sharp scissors, remove the top buds, leave 3-4 pairs of leaves, and the bare rod part is about 5cm

3, handling foam box

prepare a foam box, put a few holes in the bottom and put a few pieces of broken tiles in the bottom of the box to cut the cuckoo. p>

4. Basin soil pouring

The soil for cutting Rhododendron should be loose and breathable. You can choose to mix garden soil, cinder, sand, etc., spread about 5cm, and then spread another 5cm of matrix, which can be watered through with water

5. Cutting into soil

After watering, do not cut immediately. Wait 30 minutes for the soil to fully absorb water before cutting. Insert the cuttings into the soil about 2-3 cm

6. Water for rooting and sterilization

After cutting all the branches of Rhododendron, water again to bond the branches with the soil. After 10 minutes, pour a rooting and sterilizing water and wet the surface of the basin soil

7. Transparent film seal

is covered with a transparent film on the foam box, sealed by tape or rope, and does not need to be watered before the cuckoo is alive. Keep the foam box in a cool place and avoid direct sunlight. p>

8. Rooting and colonization

Rhododendron takes root slowly, which takes about two months. After giving birth to roots, it will be colonized with a piece of substrate

9. Pouring water

Pour the settled Rhododendron with water and place it in a ventilated and cool place for maintenance

Jasmine cutting

1. After pruning Jasmine branches

After a spring of nutrient accumulation, jasmine branches grow most vigorously after flowering. It is especially easy to take out branches and breed flower buds when cutting

2. Treatment of branches

The cut Jasmine branches are trimmed, and only two leaves are reserved for each cutting branch

Lignified branches can also be used for cutting, but ensure that there is a bud point at both ends of the branch

3. Basin soil drilling

In order to facilitate cutting, you can directly cut in the original Jasmine pot and poke several holes in the pot with chopsticks or drill bit

4. Jasmine into the basin

Insert the jasmine branch to be cutted into the poked hole and press the soil around the cuttings with your fingers

5. Water pouring and balcony maintenance

After the basin is put on, water it thoroughly at one time, and then place it on the Nanyang terrace with sufficient light for maintenance

Have you learned the post flower cutting of these flowers

If you have any questions

Welcome to communicate with Huahua in the comment area~